ROBERTS BOATS WITHOUT PLANS.
There are over 45,000 Bruce Roberts designed boats cruising the world so it
is very natural that we often receive requests for updated plans for our
designs that were built by other than the current owner.
We are always willing to assist those who have bought our boats in good
faith and now would like a set of the original, often updated plans so that
they can carry out proper maintenance on the boats and also supply copies of
the plans to the relevant authority when required to do so.
We offer these SPECIAL OWNER PLANS to those that require them at a very low
cost … if may not be your fault that you did not get the plans with the boat
so we want to help and make sure your boat is on our plan register for
For just £290 / us$425 / €385 (Way below the original cost of the plans)
we will supply you with the complete plans and bonus sheets as well as
corrections and current updates on the plans. See below as to what you
HERE is what you will receive:
You need a set of suitable boat plans including patterns. Below is listed what our design office
supplies in this regard. With the advent of modern computer yacht design we
have been able to offer the complete plans on USB. The benefit of receiving
your plans in this way is that you can have as many prints made of each
sheet as you may need.
You will receive the latest updated version of your selected boat plan, this
is only possible when you order your plans direct from the designer
including all the detailed drawings necessary to repair all parts of your
Below is listed what we consider to be a complete set of plans and full size
patterns to enable you to build your boat with the minimum time spent in
doubt as to how and what to do next!
1A All sail plans ( Sailboats ) plus these sheets cover the boats general
arrangement drawings, profile and plan views of the hull, the deck and
superstructure plus the deck plan. In the case of sailboats, the sail plan
and measurements is usually included on these sheets.
Sheet 1AA. (There may be several sheets covering various versions of the
same design). Boat Accommodation laid out and shown in plan and profile
views. The several versions of the one design are shown on separate sheets.
Also included is a list for all the materials needed to build the hull deck
Sheet 2. Boat Lines plan, show hull sections, profile including all water
and buttock lines, plan view including all water lines and buttock lines.
All frame spacing, stern or transom detail keel measurements, rudder and
skeg should all be included and all dimensions are clearly shown.
Sheet 3. This sheet will be a reduced drawing, representing what you can
expect to see, when you lay out the full size boat hull patterns. We call
this sheet the key to full size patterns; it acts as a key when arranging
the hull patterns and will enable you to readily understand just what the
patterns contain. This sheet will help you to resist the temptation of
trying to lay out the patterns on your living room floor.
Sheet 4. On this sheet you are shown how the frames were manufactured and
assembled, plus form up the stem and other parts of the basic framework.
This sheet also shows how to set up all these items on a strong back or a
system of bed-logs. The above forms the shape of your hull.
Sheet 5. This sheet will show the installation of the stringers and deck
shelf plus installing the plating in metal boats. In the case of radius
chine boats additional information is supplied on installing these plates.
Sheet 6. Now the boat is upright and this sheet covers the inside of the
hull, and shows the installation of the floor webs, bulkheads, engine beds,
and all interior stiffeners for your boat.
Sheet 7. This sheet may show detail of the various items not covered in
sheet 6. Often it takes two or more sheets to cover webs, bulkheads.
Sheet 8. This is the engineering sheet that covers the engine installation,
locating and building the fuel and water tanks plus making the rudder. Also
included are details on making the stern and rudder tubes plus propeller
shaft detail. Stanchions swim platforms and similar items may also be on
Sheet 9. This sheet shows details the forming and installation of deck
beams, side decks, foredeck, aft deck, cockpit construction and all deck
framing detail of your boat design.
Sheet 10. Patterning and making the cabin sides cabin front etc. In the case
of the cabin sides the measurements should be adequate to enable you to make
up a plywood pattern and trial fit before cutting the actual cabin side
Sheet 11. This sheet covers such items as, deck fittings, additional rudder
Sheet 12. Electrical schematics.
Sheet 13. Plumbing schematics.
Sheet 14. Exhaust systems.
Sheet 15. Tank construction.
Sheet 15. Anode sizes and placement.
Sheets 16 to 23 ...Full size patterns, A, B C, D, E, F, G & H These are the
pattern sheets that are laid together wall-paper fashion. The full size
patterns contain details of all frame shapes, stem, deck and cabin top
Also is included 1,400 Page e-book with STEP by STEP building instructions and PHOTOGRAPHS
to show you how your boat was built.
The price of the plans includes as much consultation with the designer as
YOU feel necessary to help you successfully complete the project....the
offer 'CALL BRUCE ANYTIME' is not made lightly. You can
CALL or EMAIL BRUCE ANYTIME
for advice on your boat building project.